Hyundai Veloster P2096: Post Catalyst Fuel Trim System → Too Lean → Bank 1

  P2096 is a generic OBD II code, which means that it has the same meaning for the Hyundai Veloster as it would any other vehicle.  It specifically indicates that your Veloster detected that it is running too lean (too much air for the amount of fuel present). Bank 1 is the side of the … Read more Hyundai Veloster P2096: Post Catalyst Fuel Trim System → Too Lean → Bank 1

Hyundai Veloster: High Oil Pressure → Causes + Diagnosis

If your Hyundai Veloster is experiencing unusually high oil pressure, you need to find out what’s causing it right away. Unusually high oil pressure can indicate serious problems, such as a blocked oil passage, or a broken pressure relief valve.  It should be treated like you have no oil pressure until you verify what is … Read more Hyundai Veloster: High Oil Pressure → Causes + Diagnosis

Hyundai Veloster P0606:  ECM/PCM → Processor Fault

P0606 is a generic OBD II code.  Which means that it has the same meaning for the Hyundai Veloster that it would for any other vehicle.  If your Veloster has P0606 it’s highly likely that the ECM/PCM (engine or powertrain control module, they mean the same thing) has failed. The PCM regularly performs a self … Read more Hyundai Veloster P0606:  ECM/PCM → Processor Fault

Hyundai Veloster P0603: Keep Alive Memory → Error

P0603 is a generic OBD2 trouble code.  It indicates that your Hyundai Veloster’s keep alive memory has had an error. Keep alive memory is the data that your Veloster’s PCM (Powertrain Control Module) has learned about how your engine conditions.  All of this sensor and driving input data is used to keep it operating efficiently. … Read more Hyundai Veloster P0603: Keep Alive Memory → Error

Hyundai Veloster P0522: Oil Pressure Sensor/Switch → Low Input

  P0522 is an OBD2 diagnostic code that is triggered when your Hyundai Veloster detects that the value being sent from the oil pressure sensor is below its normal operating ranged. It is typically caused by a bad oil pressure sensor or an issue with the oil system, and should be diagnosed and fixed right … Read more Hyundai Veloster P0522: Oil Pressure Sensor/Switch → Low Input

Hyundai Veloster P0336: Crankshaft Position Sensor “A” Circuit Range/Performance

The Hyundai Veloster utilizes a crankshaft position sensor (CKP) in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank. When the Veloster’s ECM determines that the signal coming from this sensor is out of range, it’ll throw the P0336 trouble code.  P0336 is most commonly caused … Read more Hyundai Veloster P0336: Crankshaft Position Sensor “A” Circuit Range/Performance

Hyundai Veloster P0125: Insufficient Coolant Temp for Closed Loop Fuel Control

P0125 is a generic OBD-II code.  If your Hyundai Veloster has registered it, means that the ECM/PCM is getting a signal from the engine coolant temperature sensor (ECT) that the engine is not warm enough to enter closed loop fuel control.  P0125 is usually caused by a bad thermostat, low coolant, or a bad ECT … Read more Hyundai Veloster P0125: Insufficient Coolant Temp for Closed Loop Fuel Control

Hyundai Veloster P0191:  Fuel Rail Pressure Sensor → Circuit “A” → Range/Performance

  P0191 is a common OBD-II code.  It indicates that the fuel rail pressure sensor is receiving a signal that is outside of its normal range.  This is a generic code, which indicates that it has the same meaning for the Hyundai Veloster as it would any other vehicle.     P0191 is typically caused … Read more Hyundai Veloster P0191:  Fuel Rail Pressure Sensor → Circuit “A” → Range/Performance