P2007 is a general DTC trouble code. It is not a very common code. If your Hyundai Genesis has P2007 it’s usually pretty easy to diagnose, although there are a few different common causes.
The most common causes of P2007 are wiring problems with IMRC Actuator, carbon deposits on the IMRC butterfly flaps, or a bad intake manifold runner position sensor.
P2007 Definition: IMRC – Stuck Closed – Bank 2
Here is the definition of P2007. Understanding it can help make diagnosis easier.
IMRC Control
Your Hyundai Genesis’s throttle body allows air into the intake manifold. Once the air makes its way through the intake, the IMRC system fine-tunes the airflow for each particular intake runner. This action creates a swirling effect that allows for more efficient combustion, which increases fuel economy and decreases emissions.
The IMRC is controlled by your Genesis’s powertrain control module (PCM). It can use either engine vacuum or an electric motor to operate the system (depending on model year and engine type). However, the vacuum-operated version does seem to be more prevalent.
Stuck Closed
The IMRC is stuck closed and can no longer fine-tune the air. If it is stuck closed, it can limit air intake at higher RPMs. This may cause some unwanted effects (covered below).
Bank 2
Each of your Genesis’s cylinder heads is considered to be a “Bank.” Bank 2 is the cylinder head with the second cylinder. Since P2007 deals with bank 2, there’s a bank one. You’ll need to determine which side of your engine has cylinder two.
If you also got P2006 when scanning your Genesis (same problem, only bank one), you should start by looking for a vacuum leak. It would be very unlikely that they’d both go out at the same time.
P2007 Symptoms: Hyundai Genesis
Here are the most common symptoms associated with P2007:
- The air-fuel mixture will be richer, at higher RPM’s
- Decreased fuel economy
- Surging Engine/Stalling
Hyundai Genesis P2007: Causes + Diagnosis
Here are things most likely to cause P2007 in your Genesis, as well as a good order of diagnostic operations:
IMRC Wiring
The wiring harness going to the IMRC and the pigtail that connects to it can cause P2007. If the IMRC actuator no longer has power, then it can’t operate the butterfly valves. This leaves the system “stuck closed”.
Check the wiring harness around your Genesis’s IMRC to ensure that it hasn’t been rubbed against anything and damaged. If it has, you’re going to need to replace or repair the wiring harness.
Make sure that the harness has the proper voltage (or voltage going to it at all). Verify that the ground is good.
Restricted Vacuum Lines (Vacuum Operated IMRC Only)
Most IMRC systems are vacuum controlled. Check the vacuum lines going to it to see if they are restricted or damaged in any way. If there is a leak, you’ll need to replace the lines.
If your Genesis has a vacuum-operated IMRC, you can control the butterfly valves with a vacuum pump (like a Mityvac). Use a vacuum pump to verify that the IMRC actuator can still operate the butterflies. If it does operate them, you know that either there’s not enough vacuum getting to the IMRC actuator for it to be effective, or something is not commanding it to turn on.
If the vacuum pump does not operate the IMRC actuator, it’s likely bad and causing P2007.
Intake Manifold and Linkage
With your Genesis’s IMRC actuator disconnected, you can operate the linkage by hand. It shouldn’t give any resistance when moving it. If it does, then it’s binding in the intake. This can happen for a few reasons:
- Carbon build-up
- Intake manifold improperly torqued
- Bent or loose IMRC butterfly valves
If the butterfly valves open and close with no resistance, you can rule out any issue with the intake, which either leaves the IMRC actuator or something causing it not to command open or closed.
If they do not freely move, there is either a carbon buildup or the butterfly valves have come loose.
Bad MAP/MAF Sensor
The PCM uses data from your Genesis’s manifold absolute pressure (MAP) or mass airflow (MAP) sensors to verify that the butterfly valves have opened as much as they should have (or at all).
If it does not see the data that it should, that can be enough to throw P2007.
Bad IMRC Actuator
Replacing the IMRC actuator is perhaps the most common fix for P2007. In the previous step, you checked all of the wiring going to it and ensured that it was good. So, at this point, it’s likely to be the IMRC actuator causing P2007.
Conclusion
As you can see, there are a lot of potential causes of P2007 in the Hyundai Genesis. Take your time, use the process of elimination, and you should have the code cleared in no time. Good luck!